Keith Plummer, Technical Manager at Ubbink, asks whether the new BS 8612 ‘Dry Fix Solutions’ will lead to a better future for all.
British Standards has recently launched BS 8612: Dry-Fixed Ridge, Hip and Verge Systems to raise and control manufacturing quality levels. This implementation has already seen some products being redeveloped and improved by manufacturers to comply with the new standards and tests.
The industry must carry the responsibility to ensure all manufacturers produce quality products — in return, specifiers select quality products, merchants supply quality products, contractors fit quality products and house owners can be assured their roof complies and will function correctly. The time is well overdue where legislation and performance stand up and be counted!
British Standard BS 5250: Control of Condensation in Building and BS 5534: Slating and Tiling have been in place for years to ensure professional and consistent building conditions are adhered to. BS 5534 was last reviewed and updated five years ago after the industry and experts deemed mortar bedding for ridge and hip less trustworthy, with a shorter lifespan than newer technologies. In turn, BS 5534 was revised stating that all ridge and hip tiles had to be mechanically fixed — even when mortar had been used to improve the fix.
BS 5250 and BS 5534:2014 were very clear on how and where the products needed to be installed to meet the requirements, however what wasn’t available was a British Standard to test the products and their durability. With more harsh and adverse weather conditions hitting the UK each year, some systems were failing which resulted in delays on sites and returns to builds to fix systems that had become loose or totally disengaged due to the high winds and snow loads.
Over the last few years in particular, Dry Verge systems have become increasingly popular as it allows not only additional securing points for the roof tiles, but replaces the need for mortar, meeting current regulations. But with the increase of products in the market, it has become more and more difficult to specify/stock a durable system — often, the products look alike with similar features but have hidden compromises to reduce cost.
Early examples of Dry Verge Systems had inherited well known and common issues such as poor quality raw material being used, resulting in units warping and just not being resilient enough. Similarly, units were being secured either to the end of an extended cut tile batten or directly to the barge board, resulting in a less secure fix.
The introduction of the Ubbink face fixing batten bracket is a key point and improves the fix immensely. If there was no barge board for the starter unit to be installed to, the contractor was forced to come up with other ways of securing the eaves unit — one way was with the use of some wire threaded through the unit and secured to a nail or screw to the fascia board, with this method deemed unacceptable under the new standards.
To overcome this problem, the Ubbink batten bracket can be used in conjunction with the starter unit to give the necessary permanent fixing.
Once the system was installed these issues were not clearly visible, so ‘out of sight out of mind’ until the bad weather hits and failings became more obvious — causing problems for all involved in the supply chain. The most common visible issue that did stand out was the allowance of rain water to either drip or run down the gable wall of the property, leaving an unsightly staining.
Industry experts soon realised that the increase in verge products on the market without any standard was proving difficult for specifiers and housebuilders to know they were selecting a trustworthy quality system with longevity.
This is where the start of BS 8612 came into fruition, with all the common factors of Dry-Fix installs being discussed and how these should — and could — be overcome to improve current builds. This gives all parties involved in the selection process, from stockists to end users, the confidence that what is being used on a project is up to a level of expectation and not a weak solution.
The new British Standard BS 8612 has been introduced to ensure that Dry Fix roofing products pass the physical demands like vertical load for wind uplift, Rain Drainage as well as an accelerated colour fast test, for aesthetics. The full independent range of tests are carried out by the experts at the Building Research Establishment (BRE) in Watford and are calibrated to indicate which of the products can be installed within the correct wind zones, if the full system has been used and installed as per the manufacturer’s instructions.
Ubbink’s Dry Fix Systems — Universal Dry Verge and Ventilated Dry Ridge Kits — are fully tested and compliant with BS8612 as tested at BRE. Many of the product features overcome the common industry issues mentioned previously, enabling a quick, easy and reliable install.
Hopefully the new testing procedures will give a greater confidence in the products, irrespective of whoever made them, for stockists, specifiers, installers and developers alike. By ensuring the reassurance that if the standards are met and the manufacturer’s instructions are followed, then there should be no need for a return to make a repair.
For more information on Ubbink’s Dry Fix Systems from the company’s website, click here.
